Blue Sea Systems Automobile Battery Charger PN 7712 User Manual |
Overview of Application
Marine Electrical Products
The ML-Series Remote Battery Switch provides high-current carrying and switching under load.
The Remote Battery Switch should be installed close to the battery banks to avoid voltage drop.
ML–Series
Remote Battery Switch (RBS)
Install a single pole double throw (SPDT) or single pole single throw (SPST) control switch in a convenient
location near other electrical controls or companionway to allow quick access in the event of an emergency
(see Illustration on reverse).*
PN 7712 / PN 7712B / PN 7714 / PN 7714B
• Magnetic Latch (ML)—draws very low current (<13 mA in the ON state and <8 mA in the OFF state) and draws
moderate current for very short time when changing state
• Silver alloy contacts provide high reliability for switching live loads
• Manual control override knob provides an added level of safety allowing control with or without power,
and offering LOCKED OFF capability for servicing
The Manual Control Override Knob provides:
• an added level of safety that allows manual ON-OFF control with or without power
• LOCK OFF for servicing the electrical system
• LED output to remotely indicate switch state
The remote LED embedded in PN 2155 indicates a closed connection between battery bank and load, or
between two battery banks when used as an emergency cross-connect.
• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Label recesses for circuit identification
• PNs 7712 and 7714 include a Remote Control Switch PN 2155
Remote Operation. PN 2155 (SPDT, ON-ON) Remote Control Contura Switch in the ON position can either
connect the battery bank to the load or combine two battery banks. In the OFF position it can either
disconnect a battery bank from a load or isolate two batteries from each other.
RBS Specifications
Cranking Rating
7712, 7712B
See Table Below
7714, 7714B
See Table Below
Intermittent Rating
Continuous Rating
Amperage Operating Current
See Table Below
See Table Below
See Table Below
See Table Below
When changing state <4A from Main
contacts returns to negative (blk) wire
To connect battery bank to load, or combine
battery banks
Set remote switch 2155 to position marked “ON”.
Remote LED indicates closed connection.
When changing state <7A from Main
contacts returns to negative (blk) wire
In “ON” state 13mA, In “OFF” state 8mA When “ON” 13mA, When “OFF” 8mA
To disconnect battery bank from load, or
isolate battery banks that are connected
Set remote switch 2155 to position marked “OFF”.
Voltage Maximum Operating
Live Current Switching
Mechanical Endurance
Control Circuit Voltage
Terminal Stud Size
16.5V DC Max.
300A @ 12V DC—10,000 Cycles
100,000 Cycles
9–16.5V DC
3/8"-16 (M10)
32V DC Max.
Remote LED Indicator embedded in PN 2155 SPDT ON-ON Contura Switch
indicates Remote Battery Switch state or condition as follows:
‡
150A @ 24V DC—10,000 Cycles
100,000 Cycles
8–32V DC
3/8"-16 (M10)
140 in-lb (15.5 N•m)
3/8", M10
LED INDICATION
LED is OFF
REMOTE BATTERY SWITCH STATE OR CONDITION
Remote Battery Switch is OFF
Maximum Terminal Stud Torque
Ring Terminal Size
140 in-lb (15.5 N•m)
3/8", M10
LED is ON
Remote Battery Switch is ON
Terminal Ring Diameter Clearance 1.18" (30.0mm)
1.18" (30.0mm)
Manual override--check Remote Battery Switch for switch states.
OR Remote Battery Switch mechanical failure
LED double blinking ON-OFF
Regulatory Meets ISO 8846 and SAE J1171 external ignition protection requirements, Rated IP66
Remote Control Switch 2155 Specifications
Emergency Manual Control Override Operations
Action
SPDT, ON-ON
Maximum Operating Amperage
Seals
Operating Temperature Range
Mounting Hole
20A @ 12V DC | 15A @ 24V DC
Internal & External Gasket Panel Seal
40°C to 85°C
To connect battery bank to load,
or combine battery banks
With Override Knob in (REMOTE position),
push button until latched (Push to Latch On).
-
1.450"x 0.830" (36.00mm x 21.08mm)
LED Rating
100,000 hours 1/2 life, 20 mA @ 14V
To disconnect battery bank from
load, or isolate battery banks that
are connected
Rotate Override Knob to right to release button
from Latch On mode (button pops up). Rotate
Override Knob to left (REMOTE position).
1
2
Regulatory Meets ISO 8846 and SAE J1171 external ignition protection requirements, Rated IP67
Wire Size (AWG)
Cranking 10 sec.
Cranking 1 min.
Intermittent 5 min. Continuous (UL 1107)
2/0
4/0
2x (4/0)
2,000A
2,000A
2,500A
750A
750A
1,100A
400A
400A
700A
225A
300A
500A
Rotate Override Knob to right
(LOCK OFF position).
To prevent remote operation
To secure for servicing
Manual Control
Control Circuit
Remote Control
Switch Included
PN
Termination
With Override Knob in (LOCK OFF position),
pass cable tie through hole.
7712
7712B
7714
Tinned Wires
Tinned Wires
Tinned Wires
Tinned Wires
Yes
Yes
Yes
Yes
12V DC
12V DC
24V DC
24V DC
SPDT, ON-ON
-
SPDT, ON-ON
-
7714B
425 Sequoia Drive
Bellingham, WA 98226 USA
p 360.738.8230
‡
Predicted performance
p 800.222.7617 USA and Canada
f 360.734.4195
* Although a SPST switch may be used if desired, use of a SPDT switch improves immunity to inadvertent
switching if the controls become damp.
980010060 Rev.002
|
Black Box Multi tool MPSH16 D20 120V User Manual
Black Decker Cordless Drill 5145557 04 User Manual
Blue Rhino Charcoal Grill CBT721W User Manual
Blue Sea Systems Marine GPS System PN9112 User Manual
Bostitch Impact Driver BTC440LB User Manual
Cabletron Systems Network Card 36 User Manual
Cannon Electric Pressure Cooker 10540G User Manual
CDA Range RV 1001 User Manual
Channel Vision Digital Camera 6401 User Manual
Chicago Electric Cordless Saw 93218 User Manual