Briggs Stratton Yard Vacuum 37610701 04 User Manual

MODEL 37610701 - 04  
PECO OWNERS MANUAL  
FOR A SCAG UNI T  
P# Q0118  
CONGRATULATIONS AND THANK YOU FOR BUYING THIS PECO LAWN VACUUM.  
Your new PeCo Vac has been engineered and manufactured to PeCo's high standards for  
safety, quality and dependability and ease of operations.  
Save This Manual For Future Reference  
PeCo  
MODEL 37610701 - 04  
 
SAFETY  
Outdoor Power Equipment Institute Recommendations  
WARNING TO PURCHASERS OF INTERNAL COMBUSTION ENGINE EQUIPPED  
MACHINERY OR DEVICES IN THE STATE OF CALIFORNIA:  
The equipment which you have purchased does not have a spark arrester muffler. If this  
equipment is to be used on any forest covered and brush covered land or grass covered  
unimproved land in the state of California, the law requires that a spark arrester muffler be  
installed and be in effective working order. The spark arrester must be attached to the  
exhaust system and comply with Section 4442 of the California Public Resources Code.  
1. Read the owner's manual carefully and familiar-  
7. Always stop Vac engine when emptying the  
ize yourself with the proper use of your attachment.  
container.  
Do not allow anyone who is not acquainted with the  
Safety Instructions to use your attachment.  
2. Know the controls and how to stop quickly.  
READ THE OWNER'S MANUAL!  
8. Stop tractor and vac engines and remove spark  
plug wire before removing or replacing hose, boot,  
blower cone or performing any maintenance.  
9. Mow up and down the face of slopes (not steeper  
3. Do not allow children to operate the vehicle. Do  
than 10 degrees); never across the face of the slope.  
not allow adults to operate it without proper instruc-  
10. It is recommended that the container be kept  
tion.  
only half full when negotiating any slopes. Start  
mowing on slopes when the container is empty.  
11. Inspect your lawn and remove any foreign ob-  
jects before mowing. Never deliberately run mower  
4. Be especially watchful of children and pets  
darting into the area while operating.  
5. Keep your eyes and mind on your tractor while  
mowing or operating your attachment. Don't let  
across any foreign object.  
others distract you.  
12. Wear ear protection if noise level is offensive.  
6. Do not attempt to operate your tractor or mower  
when not in the driver's seat.  
WARNING!  
WARNING!  
NEVER operate the mower unless the discharge  
guard and either the deflector assembly or the  
vacuum collector adapter are fastened securely in  
place.  
Do not work around the mower deck boot or the  
blower area until you are certain that the mower  
blades and the blower fan have stopped rotating.  
WARNING!  
WARNING!  
To avoid serious injury, perform maintenance on  
the vacuum collector ONLY AFTER STOPPING THE  
TRACTOR ENGINE AND WAITING FOR ALL MOV-  
ING PARTS TO COME TO A COMPLETE STOP. Set  
the parking brake. Always remove the ignition key  
before beginning the  
For your personal safety, ALWAYS mow UP and  
DOWN the face of slopes and NEVER across the  
face. NEVER attempt to mow excessively steep  
slopes and use caution when turning on any  
slope.  
maintenance  
3
PeCo  
MODEL 37610701 - 04  
 
ASSEMBLY  
MOWER  
FRAME  
STEP 1:  
Remove plate on rear of mower as shown.  
Redrill top two holes for a 3/8"-16 hex bolt  
to mount Mount Plate onto mower frame.  
HOLES TO  
MOUNT TO  
TRACTOR  
FIG. 1-1  
DESIGNATION OF  
HOLES ON THE  
MOUNT PLATE  
STEP 2:  
B
Use (2) 3/8"-16 x 2" (#K1208) , and (2)  
3/8"-16 flange nuts (#K1215) to secure  
Mount Plate (A) to mower frame. Use (2)  
1" spacers (#S0138) between Mount  
Plate (A) and mower frame. Place (1)  
Bracket (B) on each side of Mount Plate  
(A). Use (1) 3/8"-16 x 3/4" hex bolt (#K1190)  
and (1) 3/8"-16 flange nut (#K1215) to  
mount each bracket. Use existing bolts  
from mower frame to mount Bracket (B)  
to mower. Use figure 1-1 to place bolts.  
A
4
PeCo  
MODEL 37610701 - 04  
 
ASSEMBLY  
STEP 3:  
A
Slide Engine Mount Arm (B) into the receiver  
on the Mount Plate (A) and fasten by  
dropping in ball pin (#J0248). Place Engine/  
Blower Assembly onto Engine Mount Arm (B)  
and fasten with (4) 5/16"-18 x 1 1/2 hex bolts  
(#K1157) and (4) 5/16"-18 flange nuts.Tighten  
nuts and bolts.  
B
A
STEP 4:  
The ears of the Cone (A) should fit underneath  
the two threaded bosses on the Blower Face (B).  
Secure with (2) 5/16"-18 x 2" cone bolts.  
B
TIGHTEN CONE BOLTS BEFORE EACH USE!  
Impeller Blade Replacement  
To remove: Remove hex bolts from hub then screw the bolts  
into threaded holes to remove old blade.  
B
A
(This will push the impeller off the hub.) If the  
impeller is stuck on hit the base of the impeller  
between each vein with a hammer then try the  
bolts again.  
To replace: Place tapered bushing (A) into hub (B) and align  
non-threaded holes with the holes in the hub.  
Secure with two 1/4" x 1" hex bolts. Torque to 15 ft. lbs.  
5
PeCo  
MODEL 37610701 - 04  
 
PARTS LIST  
REF. NO.  
PART NO.  
DESCRIPTION  
QTY.  
1
2
3
4
5
6
B3749  
*******  
J6006  
*******  
*******  
*******  
E4052A  
D4002  
A0645  
BOOT PLATE  
BOOT (SPECIFY DECK SIZE)  
7"- 8" HOSE CLAMPS  
42" LOWER HOSE  
BLOWER CONE  
ENGINE/BLOWER/BLADE ASSEMBLY  
BLOWER HOUSING  
5HP BRIGGS & STRATTON ENGINE  
4 BLADE IMPELLAR W/ S4311 BUSHING  
W/ 3/4" SHAFT  
1
1
2
1
1
1
D1016  
A0914  
6HP KOHLER ENGINE  
4 BLADE IMPELLAR W/ S4302 BUSHING  
W/ 1" SHAFT  
7
8
9
J6011  
*******  
V1054  
A0023  
A0913  
A0931  
A0929  
A0751  
B1941  
B1926  
J0316  
A0021  
A0022  
A0236  
A08215  
V2002  
5"- 6" HOSE CLAMPS  
6"x32" UPPER HOSE  
INLET  
HARDTOP ASSEMBLY  
BASE FRAME ASSY  
(OPTIONAL) WEIGHT ASSEMBLY  
MOUNT PLATE ASSEMBLY  
ENGINE MOUNT ASSEMBLY  
INSIDE INLET PLATE  
OUTSIDE RETAINING PLATE  
GAS STRUT  
RIGHT HAND HINGE PLATE ASSEMBLY  
LEFT HAND HINGE PLATE ASSEMBLY  
LATCH ASSEMBLY  
2
1
1
1
1
1
1
1
1
1
2
1
1
2
1
10  
11  
12  
14  
16  
17  
18  
19  
20  
21  
22  
23  
24  
HARDWARE BAG  
Plastic Container 7 cu, ft,  
PeCo  
6
MODEL 37610701 - 04  
 
Exploded View of Model 376107  
10  
9
21  
22  
11  
7
20  
19  
8
23  
7
18  
6
17  
12  
16  
3
1
5
14  
2
3
4
7
PeCo  
MODEL 37610701 - 04  
 
ASSEMBLY  
STEP 5:  
Attach Base Frame (A) to Mount Plate (C) and secure by dropping in ball pin  
(#J0248). With hood open on the Base Frame (A) insert the 7cu. ft. Canister  
(B) and close  
C
REAR VIEW OF MOWER  
A
B
D
STEP 6:  
Place Clamps (A) over each end of  
6" Hose (B). Attach one end of hose  
onto Blower Housing (C). Attach free  
end of hose over Inlet (D).  
A
B
C
TIGHTEN CLAMPS!  
8
PeCo  
MODEL 37610701 - 04  
 
ASSEMBLY  
STEP 7:  
Attach Boot Retainer to Boot with 3/8" x 1"  
carriage bolts and 3/8" flange nuts as shown.  
TIGHTEN NUTS AND BOLTS!  
STEP 8:  
Lift mower deflector and hang Boot  
Plate as shown.  
STEP 9:  
Place Clamp over each end of Lower  
Hose. Attach one end of hose over  
the Blower Cone. Tighten Clamp.  
Slide free end of hose over Boot and  
tighten clamps.  
9
PeCo  
MODEL 37610701 - 04  
 
MAINTENANCE  
Your Lawn Vac was designed and built to provide years of service with only minor care. Certain  
tasks however must be performed to keep it in good operating condition and to avoid costly  
repairs. This section describes and provides procedures for the necessary care of the Lawn  
Vac.  
SCHEDULED CARE  
Before Each Use  
After Each Use  
CARE REQUIRED  
Check engine oil.  
Check all hose connections.  
Clean Collector Box, hoses and engine of all grass and dirt.  
Check that all screws, nuts, bolts, pins, etc. are present and  
secure.  
Every 10 Hours  
Storage  
Never store your Lawn Vac with a full or partially filled container; decaying grass and leaves  
may constitute a fire hazard if left too long. Never leave your vac exposed to the elements.  
While the metal parts are protected with a quality paint, the engine and other unprotected parts  
may deteriorate if left exposed to rain or snow.  
EmptyingTheLawnVac  
When the collector becomes full, the blower tone will change. In order to empty the container  
- Release the back door by moving the dump handle on the left hand side of the container.  
Release the door, push back on the container and the debris falls out. When empty, pull the  
box forward; move the dump handle in to properly close the rear door.  
Service  
PeCo Lawn Vac Owners should record the name and telephone number of their tractor  
dealer. Your dealer will be happy to supply replacement parts, accessories and do any  
service or repairs to your lawn vac. If for some reason your dealer is unable to service your  
lawn vac or supply replacement parts, contact PeCo and include the following information:  
Tractor Model: __________________________________ Year of Mfg. _________________  
Deck Size: _____________________________________  
PeCo Vac Model: _________________________  
Vac Serial Number: _______________________________  
Date of Purchase: _____ /_______ /________  
Dealer Name: _________________________________________________________________  
Dealer's City: ___________________________  
State: ______________ Zip: __________  
Dealers Phone Number: _______________________________  
10  
PeCo  
MODEL 37610701 - 04  
 
TROUBLE SHOOTING  
Diagnostic Procedures  
Trouble shooting procedures are provided in the chart below. To use these procedures,  
first locate the problem description that best describes the trouble that you have encoun-  
tered. Check the possible causes one at a time in the list. Correct any problems that are  
found and operate the vacuum collector again to verify that you have eliminated the problem.  
DO NOT attempt any major repairs without first contacting your dealer.  
PROBLEM  
CAUSE  
SOLUTION  
Leaves and Grass  
not being picked  
up completely.  
1. Engine speed too slow  
2. Ground speed too fast.  
3. Hose plugged.  
A. Run at full throttle.  
B. Use lower gear  
C. Check and tighten all hoses.  
D. Unplug hose.  
Hoses plug easily.  
1. Grass or leaves too wet.  
2. Grass too high.  
3. Container full.  
A. Wait for drier conditions.  
B. Reduce tractor ground speed/raise deck.  
C. Empty container  
4. Grass buildup in boot or  
under mower deck.  
D. Clean thoroughly.  
Vacuum Collector  
blower vibrates  
excessively.  
1. Buildup on blower blades.  
2. Bent or chipped blade.  
A. Remove cone and clean blades.  
B. Contact your dealer or PeCo.  
Unit fails to fill box.  
1. Engine speed too slow.  
2. Buildup on inlet or screen  
3. Grass is too wet or long.  
A. Run at full throttle.  
B. Clean thoroughly.  
C. Wait for dryer conditions.  
OUTDOOR POWER EQUIPMENT  
The Serial Number Plate is located  
on the aluminum box near the  
dump handle.  
Model Number  
Serial Number  
Arden, North Carolina 28704  
11  
PeCo  
MODEL 37610701 - 04  
 
P.O. Box 1197  
Arden, North Carolina 28704  
1-800-438-5823 or (828) 684-1234 fax-(828) 684-0858  
email: peco@ioa.com  
PeCo  
MODEL 37610701 - 04  
 

Belkin Battery Charger BU3DC001 12V User Manual
Black Box Computer Accessories IC 159A User Manual
Blodgett Oven S1820E User Manual
Bose Portable Speaker 250811 FRAvo User Manual
Broilmaster Gas Grill SKFB2 1 User Manual
Brother Sewing Machine 884 T09 User Manual
Canon Projector SX7 Mark II User Manual
Casio Laptop HK1223 User Manual
Char Broil Charcoal Grill 463250511 User Manual
Chevrolet Automobile 2010 Traverse User Manual